Home > Hard Drive > New Drive Setup Problems !

New Drive Setup Problems !

Contents

This is usually done by pressing the F1 key during the startup process. Flag Permalink Reply This was helpful (0) Collapse - Format the drive first by James Denison / August 25, 2015 12:31 PM PDT In reply to: The upgrade is on the If a second hard drive was added, use the following steps depending on the versions of Windows you have: Windows 7 or Vista Click Start , then click Computer. Then proceed to the section that matches the BIOS version on your computer. http://swapshaker.com/hard-drive/ide-drive-detected-but-not-displaying-in-drive-list.html

If the drive is very hot, leave the side panel off and point a standard house fan directly into the case to cool the drive. Handle the drive only by the edges or frame. arnel - 07/10/2015 Reply There are many methods to identificate a problems with hdd, but the best way i think is to hearing a sounds of your device. The remainder of the drive can be allocated later and, if you specify the maximum size, you can also shrink this size at a later time.

Install New Hard Drive Windows 7

All devices on the channel must be jumpered Cable Select. Please refer to Knowledge Base article 313348 at http://support.microsoft.com for detailed information on how to use the Disk Management tool. Cables should be carefully pulled near the connector when disconnecting from the hard drive or the system board to reduce the possibility of damage to the cable. but to the question about formatting, say yes even to the warning: data loss alert (since yours is a brand new drive, there wont be any data) and to the question

For most users, leaving it as MBR will be sufficient. If you've installed a new hard disk drive on a computer that is running Windows or want to change the partitions, use the Windows Disk Management tool. Track this discussion and email me when there are updates If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and How To Format A New Hard Drive Now, it's time to do the same for electronics.

Get the answer Half LifeNov 8, 2013, 6:51 PM what you need to do maxii is to reinstall the operating system (some version of windows, i assume). What To Do After Installing A New Hard Drive Windows Vista and 7 Click the Start Orb and in the Search programs and files text field, type diskmgmt.msc and press Enter when Computer Management is selected. Seagate  ␡ Sign In as Consumers & Non-SPP Resellers Partners & Suppliers ␡ My Dashboard My Profile Logout ␡ EXTERNAL / CONSUMER ▾ ▴ Backup & Explore ▹ Play ▹ Before replacing a hard drive for these symptoms, check the drive using the latest virus definitions.

Remove any unnecessary adapters from the system board slots. How To Install A Second Hard Drive Stand up for your right to repair. Make sure the motherboard in the computer can support the type of drive that you want to install. If you are adding an additional drive and the empty bay is part of a removable drive cage, use this section to find and unplug the cable to make the drive

What To Do After Installing A New Hard Drive

once you have it, everything else is easy. http://www.pcworld.com/article/2360427/what-to-do-when-a-second-hard-drive-bricks-your-pc.html Ask PCWorld Contributing Editor Lincoln Spector. Install New Hard Drive Windows 7 If these steps have not solved your problem refer to "Need more help?" Back to top Bad sectors Microsoft Windows may run a chkdsk program on boot up if the system Install New Hard Drive Windows 10 Disconnect the IDE or Serial ATA cable and the power cable from the back of the drive.

Connect the gray middle connector to the Slave drive. navigate here Write down each cable location if you do not already know where it connects. Press the right arrow key to open the Storage tab. You Might Like Shop Tech Products at Amazon Notice to our Readers We're now using social media to take your comments and feedback. How To Install Operating System On New Hard Drive Without Cd

  • If using a PCI SATA controller card, connect the Serial ATA cable from the drive to a SATA slot on the controller card.
  • Configuring the BIOS Close your computer case and start your computer.
  • In that case, there may be another option to select one drive over the other:But what if one of the drives doesn’t show up at all?
  • Tell them repair is good for the environment, good for consumers, and good for businesses.
  • Go to Configuring the hard drive in BIOS version 6 or less.
  • Your computer may automatically detect your new drive.
  • If it does, the original drive is defective.
  • solved PC not booting up after installing new 550W PSU but works fine on a stock 300W PSU More resources See also solved Problem after installing new motherboard Please help!
  • Reload the operating system using the available recovery media.
  • windows will take over from there.

I will try that. Additional testing of confirmed noisy drives with PC Doctor is not necessary. Do not disassemble the drive. Check This Out Power supplies may begin failing spontaneously and non-obviously, so this problem is always possible.

note: HP cannot be held liable for damage resulting from improper installation of software and/or parts, or the installation of parts and/or software that were not supplied by HP. How To Install A New Hard Drive On A Laptop A particular file may be corrupted on one copy but readable from another. HP and Compaq Desktop PCs - Installing or Replacing a Hard Drive Before you begin Installation overview video Step 1: Opening the case Step 2: Disconnecting the cables Step 3: Removing

Follow the on-screen instructions.

How is the ssd hookup now? In the menu, select the Run option, type diskmgmt.msc in the Run text field, then press Enter to open Disk Management. Promise Array Management You have Promise Array Management on your computer. New Hard Drive Not Showing Up About Us Contact Us Digital Edition Customer Service Gift Subscription Ad Choices Newsletters Privacy Policy RSS Terms of Service Agreement E-commerce Affiliate Relationships PCWorld CATEGORIES Business Laptops Mobile PC Hardware Printers

Do you think cloning my hdd to my ssd will fix the problem, if so, I might as well do it that way - it would be worth the time savings. The windows 10 upgrade has been completed. note: The images in this document might not be exactly the same as the computer you are using. this contact form Swap with another connector if possible.

In the case of troubleshooting a replacement or new option drive, check if a firmware update is available for the drive. You might need to press the key repeatedly, about once every second, until a BIOS Setup utility screen opens. If the drive uses sound and vibration insulators, use a screwdriver or install a jumper wire between the drive and chassis to ensure the drive is fully grounded. This may damage the drive.